stainless steel sheet with holes

Latest articles

stainless steel sheet with holes

...

stainless steel sheet with holes stainless steel sheet with holes

Read More
  • stainless steel sheet with holes

    ...

    stainless steel sheet with holes stainless steel sheet with holes

    Read More
  • In addition, hot-dip galvanized wire also needs to pay attention to maintenance and maintenance during use. Although it has good corrosion resistance, the zinc-iron alloy protective layer of hot-dip galvanized wire will gradually wear out after a long time of use. Therefore, regular inspection and maintenance of the surface of hot-dip galvanized wire, such as recoating or anti-corrosion treatment, helps to extend its service life.

    stainless steel sheet with holes

    ...

    stainless steel sheet with holes stainless steel sheet with holes

    Read More
  • Ordinary installation of blade thorn rope on the wall and the height of the wall in two meters up and down the general construction costs in a dozen yuan a meter, but if it is said that the height of the prison construction ordinary wall has reached four or five meters so that the construction cost of each meter is about 30 or 40 yuan, mainly because of high altitude operation risk degree is relatively large reason. The construction cost is different, but the price of blade thorn rope is the same, often the construction cost is higher than the product, which is the thorn rope factory recommends customers to use better quality blade thorn rope, which eliminates the cumbersome time and cost of subsequent demolition and installation.

    stainless steel sheet with holes

    ...

    stainless steel sheet with holes stainless steel sheet with holes

    Read More
  • During this process, each time the wire is pulled over, the surface hardens due to the high friction temperature. So basically every time you pull it you have to annealing it in the furnace. On the one hand, it is to reduce the surface hardness. On the other hand, during the process of wire pulling, only the surface is deformed, and the center is unchanged. So there’s a lot of stress inside. Therefore, it is necessary to rely on annealing to eliminate the internal stress, so that the wire becomes soft again to eliminate the stress before being drawn again.

    stainless steel sheet with holes

    ...

    stainless steel sheet with holes stainless steel sheet with holes

    Read More
  • galvanized

    stainless steel sheet with holes

    ...

    stainless steel sheet with holes stainless steel sheet with holes

    Read More
  • Regular maintenance and maintenance, save a lot of time, but also save the cost of maintenance and maintenance. With good stability, corrosion resistance, greatly prolong the service life. There are many kinds, which can be selected according to different uses. The device for making annealed wire is simple, and the utilization rate of the device is improved.

    stainless steel sheet with holes

    ...

    stainless steel sheet with holes stainless steel sheet with holes

    Read More
  • The anticorrosion of these raw materials is very different, and the use of life is not the same. Niu LAN net cold galvanized, also known as electroplating, galvanized quantity is very little, rust in rain, but the price is cheap, the use of life in 5-6 years. Hot dip galvanizing (low zinc and high zinc) on the amount of zinc in 60 grams to 400 grams, the service life is about 20-60 years, corrosion resistance is general.

    stainless steel sheet with holes

    ...

    stainless steel sheet with holes stainless steel sheet with holes

    Read More
  • stainless steel sheet with holes

    ...

    stainless steel sheet with holes stainless steel sheet with holes

    Read More
  • Hot dip galvanized coating is also relatively thick, but there is an uneven situation, for example, the thickness of the thin is only 45 microns, thick can reach 300 microns or even thicker, the color of this product is relatively dark. There is also a lot of zinc consumed in the production process. Zinc will form an infiltration layer with the metal. Its advantage is that it has good corrosion resistance. Electrogalvanizing, it is through the plating tank in the zinc one-way plating on the outside of the metal products, this way of making products is relatively slow, but its thickness is more uniform.

    stainless steel sheet with holes

    ...

    stainless steel sheet with holes stainless steel sheet with holes

    Read More
  • 

    Popular articles

    Latest articles

    Links