6x6 6 6 welded wire mesh

Latest articles

6x6 6 6 welded wire mesh

...

6x6 6 6 welded wire mesh 6x6 6 6 welded wire mesh

Read More
  • This method is generally the use of hot rolled laminated plate as raw material, the annealed steel plate is first sent to the pickling workshop, with sulfuric acid or hydrochloric acid to remove the surface of the steel sheet oxygen hot galvanizing method. After pickling, the steel plate immediately enters the tank to soak and wait for galvanized, which can prevent the reoxidation of the steel plate. After pickling, water cleaning, squeeze dry, drying, into the zinc pot, the temperature has been maintained at 445-465℃.

    6x6 6 6 welded wire mesh

    ...

    6x6 6 6 welded wire mesh 6x6 6 6 welded wire mesh

    Read More
  • 6x6 6 6 welded wire mesh

    ...

    6x6 6 6 welded wire mesh 6x6 6 6 welded wire mesh

    Read More
  • Once you find that the beginning of it has deformation, rust or broken problems must be timely correction. Generally speaking, the blade barbed rope will not be damaged simply, but it cannot be ensured that it will not happen. Because the local place where the blade barbed rope is required is generally outdoors, the probability of presenting an incident will be greatly increased. For example, in the plantation under the hillside, the blade barbed rope was damaged and deformed by stones rolling down the mountain, which requires manual correction in time, otherwise the deformed blade barbed rope will not only affect the beauty, but also lay hidden dangers for safety.

    6x6 6 6 welded wire mesh

    ...

    6x6 6 6 welded wire mesh 6x6 6 6 welded wire mesh

    Read More
  • Galvanized

    6x6 6 6 welded wire mesh

    ...

    6x6 6 6 welded wire mesh 6x6 6 6 welded wire mesh

    Read More
  • The management system of the rinsing water after the steel wire pickling should be regularly and regularly discharged after the rinsing water, and the rinsing water should be kept clean and low acid value as far as possible. The pH control is more appropriate. The concentration of plating aid should not be too high. Hot plating wire must be added ammonium chloride and zinc chloride according to the data of laboratory analysis, and the specific gravity of the composite solution is controlled in the range of 50~80g/L. The addition of ammonium chloride or zinc chloride raw materials without the results of laboratory analysis shall be subject to criticism and education, and economic treatment if necessary.

    6x6 6 6 welded wire mesh

    ...

    6x6 6 6 welded wire mesh 6x6 6 6 welded wire mesh

    Read More
  • Hot dip galvanizing, also known as hot dip galvanizing, is a method of obtaining a metal covering by immersing a steel member in a molten zinc solution. With the rapid development of high-voltage transmission, transportation and communication, the protection requirements for steel parts are becoming higher and higher, and the demand for hot-dip galvanizing is also increasing. Usually the thickness of electric galvanized layer is 5 ~ 15μm, and the large roll galvanized wire layer is generally more than 35μm, even up to 200μm. Hot dip galvanizing has good covering ability, dense coating and no organic inclusions.

    6x6 6 6 welded wire mesh

    ...

    6x6 6 6 welded wire mesh 6x6 6 6 welded wire mesh

    Read More
  • 6x6 6 6 welded wire mesh

    ...

    6x6 6 6 welded wire mesh 6x6 6 6 welded wire mesh

    Read More
  • 6x6 6 6 welded wire mesh

    ...

    6x6 6 6 welded wire mesh 6x6 6 6 welded wire mesh

    Read More
  • 

    Popular articles

    Latest articles

    Links