welded wire 16 gauge

Galvanized iron wire is divided into hot-dip galvanized wire and cold galvanized wire, using low carbon steel wire processing, after drawing forming, pickling rust removal, high temperature annealing, hot-dip galvanized, cooling and other processes. With good toughness and elasticity, the amount of zinc can reach 300 grams/square meter. It has the characteristics of thick galvanized layer and strong corrosion resistance. Galvanized iron wire can cut off the tie wire used in the building, the length is 20cm 30cm 40cm, can be cut off according to the requirements.

Annealing is to restore the plasticity of wire, improve the tensile strength of wire, hardness, elastic limit, etc., the wire after annealing is called annealing wire. In the production process of annealing wire, it is very important to ensure the quality of the finished wire, make the wire have certain strength and suitable degree of soft and hard. The annealing temperature is between 800 ℃ and 850℃, and the length of furnace tube is lengthened appropriately for enough holding time.

Flood control and flood information. Can also be used for handicrafts manufacturing, machinery and equipment of transport network mountain beautification network – high strength wire grille (hook flower net, rhombus net) the use of mountain flowers network protection principle, hook flower net, mesh uniform, flat surface, weaving concise, crochet, beautiful generous, wire mesh, mesh with wider picture, diameter of thicker, not easy corrosion, taking a long, and strong usefulness.

For single-layer wound non-rotating wire rope, it is necessary to strictly abide by the above principles, otherwise it is easy to cause permanent deformation of wire rope structure; In the case of multilayer winding, the rotation of the rope is determined by the orientation of the reel’s rope groove to lay the foundation for the next layer. The friction between the wire rope and the extrusion pressure of the multi-layer winding drum are large, and the disorderly rope phenomenon is easy to occur. Therefore, the wire rope with a diameter slightly smaller than the pitch of the rope groove and the diameter of the rope groove should be selected to add the touch area between the wire rope and the drum.

Galvanizing can be done by zincate galvanizing or chloride galvanizing. Appropriate additives shall be used to obtain a coating that meets the requirements of this standard. Luminescence treatment should be carried out after luminescence plating. The parts that need to be dehydrogenated for passivation should be passivated after dehydrogenation. Before passivation, 1%H2SO4 or 1% hydrochloric acid should be applied to activate 5~15s. Passivation shall be treated with colored chromate unless otherwise specified in the design drawings.

Dog cage mainly by welding, spraying, injection molding, surface treatment, electroplating dog cage is made of high quality steel wire, dog cages are with plastic and plastic surface treatment, electrophoresis, chrome plating, galvanized, imitation gold, etc., according to the customer request processing, respectively, also can be customized to sample, dog cage assembly of compact structure, neat and beautiful appearance, make folding and remove the cage is more convenient and quick, won’t take up too much space.

Fence use: The use of the fence is generally one meter two to two meters a height of the impregnated welding mesh, mesh mostly 6cm, wire diameter from 2mm to 3mm.

Removal of surface-active substances by activated carbon matting. Or make the bubble unstable according to overworry, these are all reasonable countermeasures; Other strategies should also be used to minimize the amount of surfactant taken in. The introduction of organic matter can make the electroplating process speed drop sharply. Galvanized iron wire blackening can be effectively prevented, such as: the work site to keep dry, reduce and do not use chemicals, operators with clean gloves and so on. In addition, hot dipping zinc factory can be required, after dipping zinc must be passivation treatment, passivation treatment of zinc has a better anti-discoloration effect, can effectively prolong the discoloration time, the combination of the two, discoloration should be able to solve.

Stainless steel material refers to air, steam, water and other weak corrosive medium and acid, alkali, salt and other chemical corrosion medium corrosion of steel, also known as stainless acid steel. In practical application, the steel with weak corrosion resistance is often called stainless steel, and the steel with chemical corrosion resistance is called acid resistant steel. And galvanized wire has good toughness and elasticity, zinc can reach 300 grams/square meter. It has the characteristics of thick galvanized layer and strong corrosion resistance. Products are widely used in construction, handicrafts, silk screen preparation, highway guardrail, product packaging and daily civil and other fields.

Generally speaking, there are three kinds of anti-corrosion and anti-rust skills: surface dipping, spraying and surface galvanized, these three ways are to strengthen their anticorrosion ability and resist natural risks, extend their service life. Today we want to talk about the difference between dip plastic hook and galvanized hook.

Because of the large size of the  barbed rope, the rope factory is used to packing. If you do not pack, then a load of blade rope can not hold many pieces, but also relatively occupy space and easy to be lost in the process of transportation.

The quality of hot-dip galvanized barbed wire is only the zinc layer attached to the surface of the wire, and with the chemical reaction, the zinc layer on the surface will gradually lose its role because of the oxidation reaction, which is more prominent in the humid environment. And because the use of rusty wire after all, it is said that the quality of hot-dip galvanized barbed wire is certainly not up to the level of stainless steel barbed wire.

1, zinc pot workers to resolutely do duty and responsibility. Do not leave the post without permission, always observe the change of steel wire galvanized layer, and according to the analysis of the results, master asbestos block gap friction need how long to press, replace the pressing face; Adjust the working face; Until the four faces of the asbestos block are used up, maintenance workers continue to use it after repair when necessary to reduce the consumption of asbestos block.