metal sheet with square holes

Latest articles

Post time: 05-08-22
metal sheet with square holes
...

metal sheet with square holes2025-08-14 21:31 【metal sheet with square holes】
Read More
3. Zinc layer structure: The structure of zinc layer includes grain size, grain shape and the combination of zinc layer and substrate, etc., which has a certain impact on corrosion resistance. In general, the finer the grain size, the denser the structure, and the better the corrosion resistance.
metal sheet with square holes
...

metal sheet with square holes2025-08-14 21:19 【metal sheet with square holes】
Read More
Before wall plastering, the wall column is connected to the gap construction wire mesh, which can play a certain strengthening and heat preservation effect. The mesh is hung on the interface surface of different grassroots, and the length of each side should meet the requirements of 100mm, so as to prevent shrinkage and cracking caused by different grassroots. Mesh wire diameter can also determine the effect and efficiency of construction, mesh fine laid up convenient soft, high construction efficiency; Of national standard can assure quality, but laid respect is inferior to fine construction fast.
metal sheet with square holes
...

metal sheet with square holes2025-08-14 21:03 【metal sheet with square holes】
Read More
Barbed wire mesh is iron mesh with high anti-corrosion function, the same is also one of the net class of iron mesh is widely used, its efficient anti-corrosion function in aquaculture, construction and other aspects are very popular. Its smooth and regular mesh surface not only increases its own beauty, but also can play a certain decoration effect.
metal sheet with square holes
...

metal sheet with square holes2025-08-14 20:40 【metal sheet with square holes】
Read More
Great attention should be paid to pickling of large rolls of galvanized wire. Acid is highly corrosive. Therefore, when adding acid, the acid must be poured into the water, and it is along the wall of the cylinder, and not thrown down at once, so as not to cause splashing. Remember the order of acid pouring, acid into water rather than water into acid, water into acid will cause splashing and boiling, when pouring acid must wear protective glasses, beside must ensure that there are no non-professional people watching, so as not to cause some acid splashing danger.
metal sheet with square holes
...

metal sheet with square holes2025-08-14 20:07 【metal sheet with square holes】
Read More
Post time: 15-02-23
metal sheet with square holes
...

metal sheet with square holes2025-08-14 20:00 【metal sheet with square holes】
Read More
Spiral blade barbed rope is also called snake abdomen type railway blade barbed rope, which is made of high quality hot dip galvanized steel plate. Galvanized wire is stuck in the middle of the barbed rope to strengthen the strength and tension. It is widely used in the outer protection of warehouses, factories and so on, and has achieved good results. The spiral blade barbed rope is connected by three clips, and the protection effect is better after opening. The standard package of the spiral blade barbed rope is 10 kg a bundle, and the service length of each bundle is about 10 meters. Such spacing makes the protection effect of the blade barbed rope reach excellent. It is widely used on the wall and the ground, and can also be composed of three-dimensional blade gill net by superposition of several phases, with better protective effect.
metal sheet with square holes
...

metal sheet with square holes2025-08-14 19:54 【metal sheet with square holes】
Read More
metal sheet with square holes
...

metal sheet with square holes2025-08-14 19:44 【metal sheet with square holes】
Read More
metal sheet with square holes
...

metal sheet with square holes2025-08-14 19:43 【metal sheet with square holes】
Read More
metal sheet with square holes
...

metal sheet with square holes2025-08-14 19:35 【metal sheet with square holes】
Read More

1
2
3
4
5
6
7
8
9
10

Popular articles

In reinforced concrete structure, the crack width of cold wire drawing is smaller than that of circular steel bar or even that of hot rolled thread bar. So cold wire drawing is more popular in the construction industry. The material for cold drawing is made of steel bars and can be simply explained how it is made, that is, its production process is simple. It’s based on steel bars, which are constantly stretched evenly, stretching the bars into something very thin, like wire drawing, without plasticity.

Our country industry chooses the low carbon steel with good quality as raw material, and then produces the quality galvanized iron wire by drawing, galvanizing and other processes. Now the production technology of galvanized iron wire products can be divided into hot plating and electroplating two kinds of methods. No matter which one is chosen, it should be carried out in accordance with the corresponding operating specifications, so as to better ensure the production of good products. For key and important parts with tensile strength greater than 1034mpa before plating, the stress should be released at 200±10℃ for more than 1 hour and 140±10℃ before plating.

Latest articles

Links