


...
insect mesh for air vents 【insect mesh for air vents】
Read More...
insect mesh for air vents 【insect mesh for air vents】
Read More...
insect mesh for air vents 【insect mesh for air vents】
Read MoreCompared with galvanizing, hot-dip galvanizing has lower production cost and less environmental impact than galvanizing. Because the coating obtained is thicker, hot-dip galvanizing has better protective performance than electric galvanizing, so it is an important protective coating for steel parts used in harsh working environment. Hot-dip galvanized products are widely used in chemical equipment, petroleum processing, ocean exploration, metal structure, electric power transmission, shipbuilding and other industries.
...
insect mesh for air vents 【insect mesh for air vents】
Read More...
insect mesh for air vents 【insect mesh for air vents】
Read MoreAnd high quality data and production cost and production conditions are bound, so some welding screen manufacturers did not meet the requirements of this aspect, natural in this case there is no way to improve product strength. In addition to data, and produce process, even if again good data, but the factory did not meet the requirements of production process in welding, also can form the product under the high pressure welding, so it is also a kind of strength on the decline, process conditions of different manufacturers also have very big difference, so it formed a shopping mall on the above products are differences of strength.
...
insect mesh for air vents 【insect mesh for air vents】
Read MoreThe large roll of galvanized silk should be coated with oil, the fiber core is dipped in oil, and the grease should be able to protect the fiber core from decay and corrosion, the iron wire moistens the fiber, and lubricates the wire rope from the inside. The surface is coated with oil so that all the wire surface in the rope strand is evenly coated with a layer of anti-rust lubricating grease, which is used for the mine rope with friction lifting and mineral water, to be coated with black grease with increased wear and strong water resistance. Other uses are coated with red oil oil with strong film and good rust resistance, and require it to have a thin oil layer, which is easy to keep clean during the operation.
...
insect mesh for air vents 【insect mesh for air vents】
Read More...
insect mesh for air vents 【insect mesh for air vents】
Read MoreSelect cut wire first of all to ensure that the raw material of the silk is exactly the raw material you need, the raw material to ensure that it will be used well. Choose the straightness is relatively high, so that the length of the truncation will be the same, there will not be a lot of length difference, the length of the truncated wire is a very important element to select the truncated wire.
...
insect mesh for air vents 【insect mesh for air vents】
Read More5, after the light plating should be carried out light treatment.
...
insect mesh for air vents 【insect mesh for air vents】
Read More5, after the light plating should be carried out light treatment.
Out-of-line annealing means that the recrystallization annealing of hot or cold rolled steel plate is carried out in the bottom type annealing furnace or cover type annealing furnace before entering the hot plating wire line, so that there is no annealing process in the galvanized line. The steel plate must maintain a clean active surface of pure iron, free of oxides and other dirt, before hot dip galvanizing. In this method, the annealed surface oxide sheet is first removed by pickling method, and then coated with a layer of zinc chloride or a mixture of ammonium chloride and zinc chloride solvent for protection, so as to prevent the plate from being oxidized again.
Welding net material has black wire, galvanized wire, wire drawing. Mesh has 1 inch, 2/1 inch, 3/1 inch, 4/1 inch, 4/3 inch, 8/5 inch, etc. Different materials, different mesh, used in different places. Therefore, welding net is an indispensable building material in construction industry.
One is to do a good job of galvanized wire packaging, avoid bumping, to ensure the integrity of the zinc layer;
Replace the column that corroded or misinterpreted and so on resulting in the loss of effect, place the replacement area together from the beginning, and reinforce the column with unstable pile foundation in time. The second is about the protection of galvanized barbed rope itself, to repair the damaged local, will be severely replaced by rust.
Our fiberglass structural shapes and pultruded fiberglass profiles are made from a combination of fiberglass and thermosetting resin systems. All shapes are lightweight, impact resistant, low maintenance, non-magnetic, low conductive, and have dimensional stability, making them easy to install and ideal for several applications. Custom shapes are available upon request. For more on fiberglass structural shapes, click here.
IMPLEMENTATION OF THE USE OF HI-GRID FRP MOLDED GRATING
As the name suggests, molded grating is created on the mold; whereas pultruded grating is created by combining the pultruded profiles in the shape of grating. Molded fiberglass grating is a combination of thermosetting resin with fiberglass roving to create a strong one piece panel.