iron nail manufacturer

Latest articles

iron nail manufacturer

...

iron nail manufacturer iron nail manufacturer

Read More
  • iron nail manufacturer

    ...

    iron nail manufacturer iron nail manufacturer

    Read More
  • In order to remove defects such as surface film layer and surface inclusion of large roll galvanized wire, it can be treated by conventional technology. The presence of small homogeneous particles of large denier in the tank can stabilize the foam layer, but the accumulation of too many solid particles can cause explosion. Activated carbon mat to remove surface active substances, or through filtration to make the foam less stable, these are effective measures; Other measures should also be taken to minimize the intake of surface active substances. The electroplating speed can be significantly reduced by the introduction of organic matter.

    iron nail manufacturer

    ...

    iron nail manufacturer iron nail manufacturer

    Read More
  • Usually according to the general people, the blade barbed rope is the guardrail, widely used in garden apartments, military bases, private residential areas, government machinery where there is a fence, generally used blade barbed rope. The biggest advantage of the blade is that the protective effect is good, and the installation and maintenance is very convenient, strong isolation ability, good resistance effect, etc.

    iron nail manufacturer

    ...

    iron nail manufacturer iron nail manufacturer

    Read More
  • 2. Dissolution treatment: Put the pickling steel wire into the dissolution tank, and dissolve the zinc powder with the bath liquid by heating, and the dissolved zinc liquid will adhere to the surface of the steel wire.

    iron nail manufacturer

    ...

    iron nail manufacturer iron nail manufacturer

    Read More
  • Large roll galvanized wire phosphating film is dark gray to black gray, the thickness is generally 5-20μm, has better corrosion resistance in the atmosphere. Membrane is a microporous structure, strong adsorption ability to paint, such as used as paint bottom, corrosion resistance can be further advanced. Metal oxidation treatment: Add steel products to NaOH and NaNO2 mixed solution, heating treatment, the surface can form a layer of thickness of about 0.5-1.5μm blue oxide film, in order to reach the purpose of steel corrosion prevention, this process is called blue treatment, referred to as blue.

    iron nail manufacturer

    ...

    iron nail manufacturer iron nail manufacturer

    Read More
  • The temperature of large roll galvanized wire should be controlled at 30 to 50℃ during electroplating. Because the chloride ions in the bath are very corrosive, quartz glass heaters are generally used. Continuous production does not need heating, but needs cooling. Cooling can be in the groove side row thin wall plastic pipe, through the flow of tap water cooling, can also be used as a titanium pipe temperature control device.

    iron nail manufacturer

    ...

    iron nail manufacturer iron nail manufacturer

    Read More
  • Traditional

    iron nail manufacturer

    ...

    iron nail manufacturer iron nail manufacturer

    Read More
  • The welding core is the metal core of the electrode. In order to ensure the quality of the weld, there are strict regulations on the content of various metal elements in the weld core. In particular, there are strict restrictions on harmful impurities (such as sulfur and phosphorus), and the quality of the weld core metal should be better than that of the base metal. Arc welding cannot be carried out on a smooth rod without a coating. This is because the arc stability is very poor, splashing is very large, and the weld is not well formed. After long-term practice, it is gradually found that the performance of the electrode is greatly improved by coating the welding core with some mineral raw materials (i.e. electrode coating). (1) Ensure stable arc combustion, so that the welding process is normal. (2) Using the gas produced after the drug skin reaction, protect the arc and the molten pool, prevent the harmful gases in the air (such as nitrogen, oxygen, etc.) from invading the molten pool, such as these gases will cause cracks and pores in the welding material, so that the welding can not achieve the ideal effect. (3) After the drug skin is melted, slag is formed, which covers the weld surface to protect the weld metal, make the weld metal slowly cool, help the gas escape, prevent the generation of pores, and improve the structure and performance of the weld. (4) After melting, various metallurgical reactions will be carried out, such as deoxygenation, sulfur removal, phosphorus removal, etc., so as to improve weld quality and reduce alloying element burning loss.

    iron nail manufacturer

    ...

    iron nail manufacturer iron nail manufacturer

    Read More
  • iron nail manufacturer

    ...

    iron nail manufacturer iron nail manufacturer

    Read More
  • 

    Popular articles

    Latest articles

    Links