dark annealed wire

For the specification of galvanized wire, the galvanized wire produced by our factory can range from No.8 to No.22, which refers to the BWG standard, that is, from about 4mm to 0.7mm, which can basically cover the type required by customers. As for the raw material of galvanized wire, normally, we use Q195 mild steel, and some factories will also use SAE1006 or SAE1008. The following is the zinc coating, for galvanized wire, this thing is more important, the general zinc coating is about 50g/m2 to 80g/m2, some customers need high zinc galvanized wire, zinc coating can reach 200g/m2 to 360g/m2. The tensile strength of galvanized wire is usually 350n/m2 to 800n/m2. Then there is the packaging specification of galvanized wire. The specifications of small rolls of galvanized wire are 50kg/ roll, 100kg/ roll and 200kg/ roll. Of course, there are large rolls of galvanized silk, the weight can reach 300kg/ roll or 800kg/ roll.

Galvanized wire is coated with a layer of stable zinc on the outside of the wire, and the zinc layer is used to protect the wire and make the service life of the wire longer. In the production of galvanized wire, the wire should be pickled. Pickling is to use some acid mist or acid liquid to wash away some oxides on the surface of iron, that is, rust, and some other corrosion, to achieve the purpose of cleaning iron, so that zinc will fall off when galvanized.

The entire steel surface is protected, and the melted zinc is easily coated evenly, whether in the interior of the pipe fitting in a depression, or in any other corner where the coating is difficult to access. The hardness of galvanized coating is greater than that of steel. The Eta layer of the upper layer of Z is only 70 DPN hardness, so it is easy to be dented by collisions. However, the hardness values of the lower layer of Zeta layer and delta layer are 179 and 211 DPN respectively, which are higher than that of the iron material of 159 DPN. Therefore, its impact resistance and wear resistance are quite good.

C, coating uniformity: galvanized layer is basically uniform with copper sulfate solution test etched five times without exposing iron.

if you compare the levels—which went as high as 50,000 milligrams/killigrams per day— to what humans are actually exposed to, we're talking orders of magnitude. It was a huge amount, Norbert Kaminski, PhD, a professor of pharmacology & toxicology and director of the Center for Research on Ingredient Safety at Michigan State University told Health.

A study published in the Journal of Agricultural and Food Chemistry in 2019 sought to examine the effects of titanium dioxide on intestinal inflammation. Researchers did this by feeding rats titanium dioxide nanoparticles and found that, after the course of two to three months, the animals had lower body weights and induced intestinal inflammation. The researchers also found the nanoparticles altered gut microbiota composition and aggravated chronic colitis. The rats also experienced reduced populations of CD4+T cells (which are cells that help organize immune responses by prompting other immune cells to fight infection), regulatory T cells, and white blood cells in mesenteric lymph nodes. The researchers wrote: “Dietary TiO2 nanoparticles could interfere with the balance of the immune system and dynamic of gut microbiome, which may result in low-grade intestinal inflammation and aggravated immunological response to external stimulus, thus introducing potential health risk.”

2.Inorganic white pigment. Widely used as a white pigment for plastics, paints and inks such as polyolefins, vinyl resins, ABS resins, polystyrene, polycarbonate, nylon and polyoxymethylene.

Titanium Dioxide prices in Germany increased by about 4% in the second quarter compared to what was seen in Q1 from historical price trends. Due to the restrictions on Russian energy imports brought on by the sanctions imposed by European countries, domestic production of TiO2 saw its costs surge even further. Additionally, the commodity's price was highlighted and its market expansion was supported by the upstream construction and automation sectors' buoyant demand.

In conclusion, the demand for dyes and pigments is on the rise, and having a reliable titanium dioxide factory like CAS 13463-67-7 is essential for meeting this demand. With its dedication to quality, sustainability, and innovation, CAS 13463-67-7 is well-positioned to continue serving the needs of its customers and the industry as a whole.