honeycomb perforated metal

Wire factory introduction annealing wire is widely used mainly because it has good elasticity and flexibility, in the process of annealing can be very good control of its soft and hard degree, it is mainly made of iron wire, more often used in the construction industry tied wire use. In the production of annealing wire will be processed according to the performance of the material, according to the demand for different degree of hardness of its soft change, can make it has more advantages, can reduce the consumption of metal, reduce the cost of production.

There are three methods to detect the thickness of zinc layer of galvanized wire: weighing method, cross section microscopy method and magnetic method, among which the first two experiments will cause certain damage to galvanized wire, including the length of galvanized wire and the reduction of dosage. The general detection of galvanized wire galvanized layer is detected by magnetic method, which is also a more intuitive and convenient method. The standard of galvanized layer thickness is related to the wire diameter of galvanized wire. The larger the wire diameter of galvanized wire, the thicker the galvanized layer is. It is the thickness of galvanized layer and cast iron after centrifugal separation.

Zinc coating on steel and ferrous metal plays an anodic role, it is commonly used for those parts subjected to atmospheric or water action, but zinc coating only when the water temperature below 60℃, the anode properties. When the temperature is higher, the potential changes and the zinc to iron becomes the cathode. Therefore, for parts subjected to hot water (such as steam boilers), the zinc skeleton must be approximately 70 microns thick and void free. For parts subjected to low or normal temperature or atmospheric action, zinc coating without pinholes is not necessary.

In recent years, with the improvement of building technology and construction standards, the demand for gypsum retarder continues to grow. New environmentally friendly gypsum retardants are gradually favored by the market, and they use more green and sustainable formulations to reduce the negative impact on the environment. Manufacturers are focusing on the development of efficient and environmentally friendly retarders to meet the sustainable development needs of the modern construction industry.

Our philosophy is

In general, gypsum retarder as a chemical additive to improve construction convenience and operability, promote the technical progress of the construction industry, while catering to the trend of sustainable development, the future market potential can not be underestimated.

We specialize in high-quality cellulose products that cater to a diverse range of industries and applications.  Our extensive experience in the field allows us to provide you with a seamless export experience, characterized by reliability and excellence.  Our team is dedicated to working closely with you to understand your specific needs and requirements, ensuring that we deliver products that not only meet but exceed your expectations.  We believe that a successful business relationship is built on trust, transparency, and mutual growth, and we are here to provide you with the necessary support and guidance every step of the way.  Whether you are looking to enhance your product line or expand your market reach, our cellulose products are designed to add value to your offerings.  Don't hesitate to reach out to us;  we are eager to assist you and discuss how we can work together to achieve your business goals.  Together, we can reject the pitfalls of traditional manufacturing processes and embrace a future defined by quality and integrity in all our products.  Welcome to our community of excellence, where your success is our priority!

Reject shirking of quality issues!

At our company, we adhere to a strong philosophy that stands firmly against the traditional practices of harmful adulteration and the inconsistencies that often plague product quality from one batch to the next.  We recognize that in today's competitive market, maintaining high standards is not just an option but a necessity.  Therefore, we take pride in our commitment to quality assurance, ensuring that our products consistently meet the highest standards, eliminating any possibility of shirking quality issues.  If you are considering venturing into the world of exporting, we invite you to partner with us.

This demonstration serves not only as a platform for knowledge sharing but also as a strategic initiative to foster collaboration and build stronger partnerships with entities that rely on advanced materials.   The insights and data gathered during this session will contribute to ongoing research and development efforts, ultimately facilitating the introduction of new products that harness the unique benefits of HPMC.   Overall, the successful execution of this experiment underscores the company's commitment to technological advancement and excellence in service delivery, thereby reinforcing its reputation in the market as a trusted provider of specialty chemicals and materials.

On the previous day, the technical team of the company convened at the office to conduct a comprehensive experimental demonstration focusing on Hydroxypropyl Methylcellulose (HPMC).

Our philosophy is

Reject traditional malicious adulteration!

This demonstration serves not only as a platform for knowledge sharing but also as a strategic initiative to foster collaboration and build stronger partnerships with entities that rely on advanced materials.   The insights and data gathered during this session will contribute to ongoing research and development efforts, ultimately facilitating the introduction of new products that harness the unique benefits of HPMC.   Overall, the successful execution of this experiment underscores the company's commitment to technological advancement and excellence in service delivery, thereby reinforcing its reputation in the market as a trusted provider of specialty chemicals and materials.

At our company, we adhere to a strong philosophy that stands firmly against the traditional practices of harmful adulteration and the inconsistencies that often plague product quality from one batch to the next.  We recognize that in today's competitive market, maintaining high standards is not just an option but a necessity.  Therefore, we take pride in our commitment to quality assurance, ensuring that our products consistently meet the highest standards, eliminating any possibility of shirking quality issues.  If you are considering venturing into the world of exporting, we invite you to partner with us.

Adhesive mortars are one of the primary applications of HPMC, wherein a specific dosage of hydroxypropyl methylcellulose, typically ranging from 1.5 to 2.5 kg per ton, is incorporated into the mixture to achieve optimal performance. This mortars are mechanically blended with cement, quartz sand, and polymer binders combined with various additives to create a reliable adhesive for bonding insulation boards. Known as polymer insulation board adhesive mortar, it is formulated using high-quality modified special cements and various high-molecular weight materials that provide superior water retention and exceptional bonding strength. This adhesive type is crucial in the construction industry, especially in ensuring energy efficiency and thermal performance in buildings by effectively adhering insulation materials to the substrate.

This session was meticulously organized to showcase the exceptional high viscosity properties of HPMC, a critical attribute that underlines its versatile applicability across various industries.  The demonstration aimed to provide stakeholders, including researchers and potential clients, with a clear understanding of how HPMC performs under specific conditions, emphasizing its efficacy as a thickening, binding, and stabilizing agent.   Throughout the event, the technical personnel engaged in detailed discussions and hands-on presentations, illustrating the various methods of integrating HPMC into formulations and processes.   The outcomes highlighted not only the material's effectiveness in enhancing product consistency and texture but also its role in improving the overall performance of formulations across diverse applications.   By meticulously examining the high viscosity characteristics, the team aimed to solidify the company’s position as a leader in supplying innovative and reliable solutions tailored to meet industry demands.   

Reject shirking of quality issues!

Reject shirking of quality issues!

The application of gypsum retarder is very wide, including wall plastering, ceiling, decorative modeling and so on. It ensures the flexibility of construction operation without affecting the physical properties and aesthetics of the finished product. This makes the chemical one of the indispensable materials in modern construction.

The main components of gypsum retarder can include a variety of organic and inorganic substances, such as sodium citrate, tartaric acid and so on. By reacting with dissolved components in gypsum, these substances delay the hydration reaction rate of gypsum, thus delaying the initial and final coagulation time. This delay does not affect the final strength of the plaster, ensuring the durability and stability of the finished product.

The main components of gypsum retarder can include a variety of organic and inorganic substances, such as sodium citrate, tartaric acid and so on. By reacting with dissolved components in gypsum, these substances delay the hydration reaction rate of gypsum, thus delaying the initial and final coagulation time. This delay does not affect the final strength of the plaster, ensuring the durability and stability of the finished product.

This demonstration serves not only as a platform for knowledge sharing but also as a strategic initiative to foster collaboration and build stronger partnerships with entities that rely on advanced materials.   The insights and data gathered during this session will contribute to ongoing research and development efforts, ultimately facilitating the introduction of new products that harness the unique benefits of HPMC.   Overall, the successful execution of this experiment underscores the company's commitment to technological advancement and excellence in service delivery, thereby reinforcing its reputation in the market as a trusted provider of specialty chemicals and materials.

Hydroxypropyl methyl cellulose (HPMC) significantly influences the properties of cement mortar, particularly in its early stages, where it may slightly reduce strength by increasing porosity and absorbing water, which can hinder the cement’s hydration process. However, the long-term impact of HPMC is multifaceted. Its water retention capability sustains hydration, thereby enhancing strength over time. Furthermore, HPMC improves the internal structure of mortar, contributing to stability and durability, which ultimately influences strength positively. The functions of HPMC in mortar are diverse; it primarily serves to retain moisture, preventing rapid evaporation during application processes like masonry, which reduces the risk of cracking and compromised strength. Additionally, HPMC exhibits thickening properties that enhance viscosity, facilitating easier and uniform application while preventing sagging, especially on vertical surfaces. This ensures better adhesion and resistance to gravity-induced displacement. Moreover, HPMC improves the overall workability of mortar, making it simpler to mix, transport, and apply, thus improving construction efficiency and minimizing waste. It also plays a vital role in enhancing durability by improving frost resistance and impermeability, crucial in cold or humid conditions. However, dosage control is essential, as inadequate or excessive amounts can adversely affect mortar strength and performance. Optimal HPMC dosage should be determined experimentally, and thorough mixing is necessary to ensure uniform distribution within the mortar. Proper storage conditions are also vital; HPMC must be kept in a dry environment away from direct sunlight and extreme temperatures to maintain its efficacy. Overall, while HPMC presents various benefits, careful management of its application and dosage is key to maximizing its advantages in cement mortar.

Gypsum retarder is an important construction additive, designed to extend the setting time of gypsum materials, thereby improving the operability of construction. This chemical is widely used in the construction industry, especially in projects requiring a long construction time, and plays a vital role. Due to the short setting time of traditional gypsum, it limits the large-scale and complex construction process, and after the addition of retarder, workers can more easily carry out fine construction and adjustment, ensuring the construction quality and efficiency.

Reject shirking of quality issues!

We specialize in high-quality cellulose products that cater to a diverse range of industries and applications.  Our extensive experience in the field allows us to provide you with a seamless export experience, characterized by reliability and excellence.  Our team is dedicated to working closely with you to understand your specific needs and requirements, ensuring that we deliver products that not only meet but exceed your expectations.  We believe that a successful business relationship is built on trust, transparency, and mutual growth, and we are here to provide you with the necessary support and guidance every step of the way.  Whether you are looking to enhance your product line or expand your market reach, our cellulose products are designed to add value to your offerings.  Don't hesitate to reach out to us;  we are eager to assist you and discuss how we can work together to achieve your business goals.  Together, we can reject the pitfalls of traditional manufacturing processes and embrace a future defined by quality and integrity in all our products.  Welcome to our community of excellence, where your success is our priority!

In general, gypsum retarder as a chemical additive to improve construction convenience and operability, promote the technical progress of the construction industry, while catering to the trend of sustainable development, the future market potential can not be underestimated.

Reject uneven product quality from batch to batch!

Reject uneven product quality from batch to batch!

We specialize in cellulose product, We can provide you with a perfect experience~

We specialize in cellulose product, We can provide you with a perfect experience~

In recent years, with the improvement of building technology and construction standards, the demand for gypsum retarder continues to grow. New environmentally friendly gypsum retardants are gradually favored by the market, and they use more green and sustainable formulations to reduce the negative impact on the environment. Manufacturers are focusing on the development of efficient and environmentally friendly retarders to meet the sustainable development needs of the modern construction industry.

Our philosophy is

Hebei ShengShi HongBang Cellulose Technology Co., Ltd., located in the Xinji Provincial Clean Chemical Industry Park in Hebei Province, is a distinguished manufacturer specializing in Hydroxypropyl Methylcellulose (HPMC). As part of the Beijing Tianjin Hebei metropolitan area, the company prides itself on leveraging advanced technology and high-quality materials to produce HPMC, which finds extensive applications in various sectors, particularly construction. HPMC is a crucial additive widely recognized for its properties that enhance the performance of construction materials, such as adhesive mortar, mortar plaster, and insulation materials. The company is committed to continuous innovation and meeting the evolving needs of the industry, ensuring that its products deliver excellent quality and performance.

This session was meticulously organized to showcase the exceptional high viscosity properties of HPMC, a critical attribute that underlines its versatile applicability across various industries.  The demonstration aimed to provide stakeholders, including researchers and potential clients, with a clear understanding of how HPMC performs under specific conditions, emphasizing its efficacy as a thickening, binding, and stabilizing agent.   Throughout the event, the technical personnel engaged in detailed discussions and hands-on presentations, illustrating the various methods of integrating HPMC into formulations and processes.   The outcomes highlighted not only the material's effectiveness in enhancing product consistency and texture but also its role in improving the overall performance of formulations across diverse applications.   By meticulously examining the high viscosity characteristics, the team aimed to solidify the company’s position as a leader in supplying innovative and reliable solutions tailored to meet industry demands.   

The main components of gypsum retarder can include a variety of organic and inorganic substances, such as sodium citrate, tartaric acid and so on. By reacting with dissolved components in gypsum, these substances delay the hydration reaction rate of gypsum, thus delaying the initial and final coagulation time. This delay does not affect the final strength of the plaster, ensuring the durability and stability of the finished product.

The application of gypsum retarder is very wide, including wall plastering, ceiling, decorative modeling and so on. It ensures the flexibility of construction operation without affecting the physical properties and aesthetics of the finished product. This makes the chemical one of the indispensable materials in modern construction.

Our philosophy is

This session was meticulously organized to showcase the exceptional high viscosity properties of HPMC, a critical attribute that underlines its versatile applicability across various industries.  The demonstration aimed to provide stakeholders, including researchers and potential clients, with a clear understanding of how HPMC performs under specific conditions, emphasizing its efficacy as a thickening, binding, and stabilizing agent.   Throughout the event, the technical personnel engaged in detailed discussions and hands-on presentations, illustrating the various methods of integrating HPMC into formulations and processes.   The outcomes highlighted not only the material's effectiveness in enhancing product consistency and texture but also its role in improving the overall performance of formulations across diverse applications.   By meticulously examining the high viscosity characteristics, the team aimed to solidify the company’s position as a leader in supplying innovative and reliable solutions tailored to meet industry demands.