4x4 welded wire panels
Latest articles
The tensile resistance of welding net to 120N, otherwise for unqualified welding net. In this respect, there is no simple way to test the tensile resistance of the welding net, only through professional tools, expert testing to test, we will not introduce in detail. The outcrop on both sides of the welding net should not exceed 2MM. The welding net diameter wire and weft wire crossing place should be welded firmly, but the edge of the welding net to weld firmly weft wire must come out some, to weld firmly, but can not come out too much, generally not more than 2 mm is qualified welding net.
4x4 welded wire panels...
4x4 welded wire panels 【4x4 welded wire panels】
Read MoreThe advantage of the steel mesh sheet is that the steel mesh sheet ensures the quality of the project and is made by the automatic and intelligent production line under the strict quality control of the factory. The mesh size, steel bar specifications and quality of the steel mesh are strictly controlled. Avoid artificial mesh leakage, bonding is not strong, bonding error and Jerry construction. The mesh steel has large rigidity, outstanding elasticity, uniform, accurate spacing and high welding point strength. Thus greatly improve the quality of the project.
4x4 welded wire panels...
4x4 welded wire panels 【4x4 welded wire panels】
Read More
4x4 welded wire panelsThe use of electric welding mesh is very wide, can be used in many places. In the field of construction, especially the wall crack, has played a very important role, the traditional construction, is to put on mortar directly onto the wall, after such a long time, will appear fall off and fracture phenomenon, in order to prevent the occurrence of this phenomenon, must use welded wire mesh before rendering, welded wire mesh is fixed to the wall, above the plastering construction, Can ensure that the wall level for a long time, not easy to crack phenomenon.
...
4x4 welded wire panels 【4x4 welded wire panels】
Read More4x4 welded wire panels
...
4x4 welded wire panels 【4x4 welded wire panels】
Read More
4x4 welded wire panelsEnclosure to calculate the use of barbed rope, so as to reasonably plan to purchase the amount of barbed rope to facilitate construction
...
4x4 welded wire panels 【4x4 welded wire panels】
Read MoreGalvanized iron wire is divided into hot galvanized wire and cold galvanized wire, the use of low carbon steel wire processing, after drawing molding, pickling rust removal, high temperature annealing, hot galvanized, cooling and other processes. Good toughness and elasticity, zinc content can reach 300 grams/square meter. It has the characteristics of thick galvanized layer and strong corrosion resistance. Galvanized iron wire can be cut off the tie wire used in the building, the length of 20cm 30cm 40cm, can be cut off according to requirements.
4x4 welded wire panels...
4x4 welded wire panels 【4x4 welded wire panels】
Read More
4x4 welded wire panels1. Zinc pot operators must stick to their posts
...
4x4 welded wire panels 【4x4 welded wire panels】
Read More4x4 welded wire panels
...
4x4 welded wire panels 【4x4 welded wire panels】
Read More4x4 welded wire panels
...
4x4 welded wire panels 【4x4 welded wire panels】
Read More
4x4 welded wire panelsThe production process is to roll the hot metal billet into 5mm thick steel, and then put it into the wire drawing device, draw into different diameters of the line and gradually reduce the aperture of the wire drawing disk. Production process through cooling, annealing, coating and other processing technology, and then made into a variety of different specifications of galvanized wire. Galvanized wire production because of simple process, wide application, early development. Galvanized wire or steel wire is a cold working product of steel wire, and the material used is generally low carbon steel or stainless steel.
...
4x4 welded wire panels 【4x4 welded wire panels】
Read More
Popular articles
Post time: 29-03-23
Post time: 09-09-22In order to pack and bind galvanized wire in the surface of the sedimentary layer to local removal of surface film, surface inclusion and other defects can be found and treated by conventional technology; Excess foam is formed when soap and surfactants such as saponified fats are brought into the tank. Moderate rates of foam formation may be harmless. Small, homogeneous particles of large denier present in the bath can stabilize the foam layer. Use activated carbon mat to remove surface active substance. Or through filtration to make the foam is not too stable, which are effective measures; Other measures should also be taken to reduce the amount of surfactant introduced. The electroplating speed can be obviously reduced by the addition of organic matter. Although chemical formulations facilitate high deposition rates, the deposition of organic matter does not meet the requirements of coating thickness, so activated carbon can be used to treat the bath.
- Packaging and binding electric galvanized wire is in the state of liquid zinc, after messy physical and chemical effects, not only on the steel plating thicker pure zinc layer, and also generate a zinc – iron alloy layer. This plating method not only has the corrosion resistance characteristics of galvanized wire, but also has a zinc-iron alloy layer. It also has strong corrosion resistance that can not be compared with galvanizing. Therefore, this plating method is especially suitable for all kinds of strong acid, alkali fog and other strong corrosion environment.
Latest articles
-
During this process, each time the wire is pulled over, the surface hardens due to the high friction temperature. So basically every time you pull it you have to annealing it in the furnace. On the one hand, it is to reduce the surface hardness. On the other hand, during the process of wire pulling, only the surface is deformed, and the center is unchanged. So there’s a lot of stress inside. Therefore, it is necessary to rely on annealing to eliminate the internal stress, so that the wire becomes soft again to eliminate the stress before being drawn again.
-
For the barbed rope products produced by the barbed rope factory, the number of rotating turns between the two thorns is usually 3-5. What is the internal relationship between this and the length of use?
-
-
-
-
2.7*2.25mm means that the two strands are 2.7mm silk, and the thorns are 2.25mm silk.
Links
- As new coal-fired power plants come on line to meet the growing demand for electricity in the US and around the world, there is an increasing need to clean plant emissions to meet clean air regulations. Special pumpsxa0help to operate these scrubbers efficiently and handle the abrasive slurries used in the flue gas desulphurisation (FGD) process.
- Sites often rely on centrifugal pumps to provide slurry service. These pumps (and their associated piping systems) require special provisions that demand detailed knowledge of the properties of solids and slurries to prevent wear, corrosion, erosion and other adverse effects such as solids settling. Specifying the optimum combination of speed, geometry and material requires a proper balance of often conflicting pump priorities; this requires consideration of stable operation, maximum wear life, operational flexibility and minimum energy consumption.
- - Hydraulic efficiency is as important as the material, as efficiency is related to wear. The swept-back design of the impeller blades minimises the separation of solids from the carrying fluid, resulting in a more uniform flow. This results in a slower wear rate.
- 1.Find the spot that allows the pump to run as slow as possible (to reduce wear), but fast enough to keep solids from settling and clogging the lines.To reduce wear, lower the pump’s discharge pressure to the lowest point possible. Follow proper piping principles to ensure a constant and uniform delivery of the slurry to the pump.
- Aier Machinery has strong technical force and is specially engaged in the research of abrasion resistant materials of slurry pumps, sewage pumps and water pumps and the development of new products. The materials include high chrome white iron, duplex stainless steel, stainless steel, ductile iron, rubber, etc.
- Is the discharge configuration suitable for abrasive slurries?
- - Easy installation - Submersible pumps are relatively easy to install since the motor and worm gear are a single unit.
- Slurry Pump
- Longer maintenance intervals
- The length of the piping. The longer the pipe, the more slurry-induced friction the pump needs to overcome.
- We use CFD, CAD method for product design and process design based absorbing experience of world leading pump companies. We integrate molding, smelting, casting, heat treatment, machining and chemical analysis, and have professional engineering and technical personnel.
- For certain types of slurry pumping conditions, positive displacement pumps may be a more suitable option than centrifugal pumps.
- If you want to get more information about the slurry pumps for sale, welcome to target=_blank title=Contact Us>contact us.
- factors-to-consider-when-choosing-a-slurry-pump
- Choosing the right slurry pump
- Slurry Pump
- Slurry Pump VS Mud Pump
- Slurry pump vs mud pump
- There is a better way to pump sewage, overflows and other collected dirty water around the plant.
- Slurry Pump
- Slurry pump design
- Slurry pump power adjustment
- Light-duty Slurry Pump
- Stainless Steel, Duplex Stainless Steel, Ductile Iron, Grey Iron, etc. We can also provide natural rubber, elastomer rubber parts and pumps.
- The discharge branch can be positioned at intervals of 45 degrees by request and oriented to any eight positions to suit installations and applications. There are many drive modes for option, such as V-belt, flexible coupling, gearbox, hydraulic coupler variable frequency, silicon controlled speed, etc. Among them, the flexible shaft coupling drive and V-belt feature of low cost and easy installation.
- Sump drainage or washdown
- Aier Machinery's team of consultants are on hand to provide you with a solution to your needs. Whether you are planning to purchase a slurry pump or need spare parts for an existing pump, we will help you determine your needs and provide advice on fine-tuning your equipment to your specific application.
- Discharge ports can be placed at 45 degree intervals and oriented in up to 8 different positions depending on your needs.
- Mechanical Seals
- What style of pump is suitable?
- - Smaller, more efficient tank - Because the motor is cooled by the surrounding liquid, the submersible slurry pump can be started up to 30 times per hour, resulting in a smaller, more efficient tank.
- Slurry Pump Selection
- Advantages of rubber
- Aier Machinery Hebei Co., Ltd. is a large-scale professional >slurry pumps manufacturer, gravel pumps, dredge pumps, sewage pumps and clean water pumps in China.
- The company uses advanced computer assistant engineering software to design products and technology, which makes our method and level of design reach international advanced level. The company has the first-class pump performance testing station in the world, and its test capacity can reach 13000m³/h. Annual output of our products is 10000 sets or tons on high chrome alloy castings. Main products are Type WA, WG, WL, WN, WY, WZ, etc. Size: 25-1200mm,
- Types of slurry pumps
- Consider the pump components
- WY type pump casing is made of abrasion resistant metal, impeller material can be abrasion resistant metal or rubber. The submerged parts of WYJ are all lined with rubber, for transfer corrosive slurry.
- Step 3
- To reduce component wear, most centrifugal slurry pumps run at fairly low speeds - typically less than 1200 rpm. Find the optimum position that allows the pump to run as slowly as possible but fast enough to prevent solids from settling out of the slurry deposit and clogging the lines.
- The first major requirement for >slurry pumps is to provide adequate service life. The erosive and corrosive effects of slurries, such as the impact of high velocity flow of liquid/solid mixtures, can be really challenging. In many applications, some of the solids in the mixture are larger than the particles normally specified; therefore, the pump should be able to pass through them without causing any damage or operational problems.
- Slurry pumps can be used to transport mixtures of liquids and solids in many industries in a wide range of applications, such as mine drainage, dredging of sunken lagoons and pumping of drilling mud.
- If you want to get more information about the slurry pump for sale, welcome to target=_blank title=Contact Us>contact us.
- The solution is to choose a >heavy duty slurry pump and, just as importantly, to use a custom built unit with replaceable parts. At Aier Machinery, building your custom slurry pump is one of our areas of expertise. We design your slurry pump to your specifications and application.
- 3. Both pumps and motors are designed separately.
- In addition, a new level of complexity is added to an otherwise simple machine. Other parts must now be inventoried and training beyond basic spanner turning is required. When it comes to pumping rock and some of the world's most abrasive materials.
- Expertise and experience
- Choosing the right pump for your slurry is critical to getting the most out of it. Basic pump components such as impeller size and design, materials of construction and discharge configuration must be considered to ensure that the pump can withstand the wear caused by abrasive slurries. Compared to low-viscosity liquid pumps, target=_blank title=Slurry Pump>slurry pumps are typically larger and often require more horsepower to operate because they are less efficient. Bearings and shafts must also be more robust and durable.
- - Smaller, more efficient tank - Because the motor is cooled by the surrounding liquid, the submersible slurry pump can be started up to 30 times per hour, resulting in a smaller, more efficient tank.
- What is slurry?