304 stainless steel expanded metal

Cold galvanized wire refers to a process in which ordinary steel wire is treated by cold galvanized and a zinc layer is attached to its surface. Cold galvanized wire has the advantages of anti-corrosion and anti-wear, and is widely used in construction, machinery, automobile, electronics and other industries. The following will introduce the production process and flow of cold galvanized wire.

The design is designed not only for ease of installation, but also for the ability to achieve such installation in harsh terrain conditions such as cliffs, with little anchorage and little excavation for quick and easy installation. Based on the characteristics of heavy hexagonal mesh double stranded structure, even in the case of wire damage can also withstand the impact of falling rock.

Use in daily life does not need to carry out maintenance and maintenance, save a lot of time, but also save maintenance and maintenance costs. The annealed wire has good stability and corrosion resistance, which greatly prolongs its service life. There are many kinds, which can be selected according to different uses. The device for making anneal wire is simple, which improves the utilization rate of the device. The material properties of annealed wire can meet different processing requirements.

A pet carrier can be used as an indoor or outdoor pet house. The dog cage is equipped with a fixed food basin and water fountain, and the foot plate pet cage rubber pad has bayonets on four sides to be splintered. It can be spliced, cut and disassembled according to the size of the cage. It is convenient and easy to clean. It can solve the problem of pinching the feet of the puppies in the ordinary cage and prevent the puppies from causing adverse reactions in the development. The dividers are breathable and comfortable, and can be used as heat shields for pets in summer. A puppy with small feet, no feet, no pinching.

When the coating of large galvanized wire is blistered in the process of galvanizing, the bath temperature should be checked first. If the bath temperature is not low, and then strengthen the removal of oil before plating, to prevent the base metal in acid corrosion. If you pay attention to these problems, the bubbling phenomenon still exists, it should pay attention to the dosage and quality of additives, then you can stop adding additives, with high current electrolysis for a period of time, to reduce the content of additives, observe whether the bubbling phenomenon is improved. If there is no improvement, check whether the additive has been stored for too long or whether it contains too many impurities.

In our daily life, what we can bend with our hands is basically galvanized iron wire, not steel wire. It has a high zinc content, which ensures excellent toughness and resilience, as well as ultra-high corrosion resistance, which can be maintained in outdoor environments for decades. There are many practical galvanized iron wire, such as strong reliability, galvanized layer and iron together, forming a special metallurgical structure, in the use and transportation process, can ensure that it will not be mechanical damage.

The different spacing of the thorn rope is mainly in order to save costs to consider, because if they are too close, then obviously a little waste of resources, but the installation is too sparse will not work. Usually the bottom spacing is about 10cm, and the top is up to 20cm, this is because the higher the place is more difficult to climb over, usually more than one meter without the help of tools it is difficult for ordinary people to climb over, and the bottom because of the relatively tight can prevent personnel from drilling in the past.

3, with oil cloth (oil used cloth), carefully from inside to outside, including each cage wire repeatedly grinding many times. The front of the bird cage, the door flowers, where vision is often in place, are repeatedly rubbed in order to improve the surface finish, equivalent to “grinding”. Note: door flowers, arhat lines and other structures are delicate and fragile, do not break. This process, which requires time and patience, care, is also a process of observing and appreciating the cage. Use new cloth again, according to the above process, wipe again and again. This process is equivalent to polishing. For important parts, you can use a little force, the speed can be a little faster (do not use force). Be careful to fold the cloth neatly, otherwise marks will easily form. When this process is complete, the surface finish is significantly improved.

The formation process of hot dip galvanized layer is the process of forming iron-zinc alloy between the iron matrix and the outside pure zinc layer. The surface of the workpiece forms the iron-zinc alloy layer during the hot dip plating, so that the iron and pure zinc layer is well combined. The process of large roll galvanized wire can be simply described as: when the iron workpiece is immersed in the molten zinc solution, the first zinc and α-iron (body-centered) solid melt is formed on the interface. This is a crystal formed by the matrix metal iron dissolved with zinc atoms in the solid state. The two metal atoms are fused with each other, and the gravitational attraction between the atoms is relatively small.

Hexagonal net value is quite high in landslides, many slope through the baptism of the rain after this, there may occur sediment flow of plague and as a result some losses to the property of the people, have the existence of hexagonal wire netting, can solve this problem, from the fundamental up sediment flow in came it can help guard against protection, achieve low is the loss of many people.