15 degree coil nails 1 1 2

Latest articles

15 degree coil nails 1 1 2

...

15 degree coil nails 1 1 2 15 degree coil nails 1 1 2

Read More
  • The external environment has great influence on the preservation of galvanized wire mesh. In the rainy season, it is necessary to pay attention to the air humidity of the workshop, warehouse and other departments. It is recommended to use a humidifier. Usually, the moisture absorption of book paper is larger than that of powder paper, and the pH value is higher. Generally speaking, in the normal environment of storage wire, storage time of two years is not corroded wire phenomenon. However, it should be noted that in the process of handling the iron wire, it should be handled gently to avoid the position of the coiling coil, which will cause the smooth pulling of the wire and affect the production.

    15 degree coil nails 1 1 2

    ...

    15 degree coil nails 1 1 2 15 degree coil nails 1 1 2

    Read More
  • Cold drawing wire is a metal cold processing, with wire rod as raw material, that is, the mouth of the steel bar. Cold drawing wire is a product produced by a series of processes such as shell stripping, which is a common wire. In the development and production of metal materials, cold drawing wire is a very common material, its performance is good, the range of use is very wide, manufacturers in processing are the use of cold processing to produce.

    15 degree coil nails 1 1 2

    ...

    15 degree coil nails 1 1 2 15 degree coil nails 1 1 2

    Read More
  • 2.0*2.0mm 12 meters per kilogram

    15 degree coil nails 1 1 2

    ...

    15 degree coil nails 1 1 2 15 degree coil nails 1 1 2

    Read More
  • A. When the thickness of the plating is 3-4 mm, the zinc adhesion should be less than 460g/m, that is, the average thickness of the zinc layer is not less than 65 microns.

    15 degree coil nails 1 1 2

    ...

    15 degree coil nails 1 1 2 15 degree coil nails 1 1 2

    Read More

  • Post time: 09-03-23

    15 degree coil nails 1 1 2

    ...

    15 degree coil nails 1 1 2 15 degree coil nails 1 1 2

    Read More
  • Compared with galvanizing, hot-dip galvanizing has lower production cost and less environmental impact than galvanizing. Because the coating obtained is thicker, hot-dip galvanizing has better protective performance than electric galvanizing, so it is an important protective coating for steel parts used in harsh working environment. Hot-dip galvanized products are widely used in chemical equipment, petroleum processing, ocean exploration, metal structure, electric power transmission, shipbuilding and other industries.

    15 degree coil nails 1 1 2

    ...

    15 degree coil nails 1 1 2 15 degree coil nails 1 1 2

    Read More
  • In the corner area, the zinc layer is often thicker than other places, and has good toughness and abrasion resistance. And other coatings in this corner, often Z thin Z is not easy to construction, Z is easy to hurt, so often need to be maintained. Even if there’s a lot of mechanical damage or something. Causing a small layer of zinc to peel off, leaving the iron base exposed, the surrounding zinc layer will act as a sacrificial anode to protect the steel from erosion.

    15 degree coil nails 1 1 2

    ...

    15 degree coil nails 1 1 2 15 degree coil nails 1 1 2

    Read More
  • 15 degree coil nails 1 1 2

    ...

    15 degree coil nails 1 1 2 15 degree coil nails 1 1 2

    Read More
  • Pressure welded steel grid plate is the steel grid plate fixed by pressure resistance welding at each intersection of bearing flat steel and transverse bar, which is called pressure welded steel grid plate. Torsion torsion square steel is generally used for cross bar of pressure welded steel grid. Although they do not belong to the same variety, but in the steel lattice plate standards and performance are still the same.

    15 degree coil nails 1 1 2

    ...

    15 degree coil nails 1 1 2 15 degree coil nails 1 1 2

    Read More
  • 

    Popular articles

    Latest articles

    Links